Open Frame FSP150 - P35 - A24 150W 24V 6.25A PSU with IEC 62368 Standard

This FSP-150-P35-A24 AC-DC switching power supplies in a package of 3 x 5 inches is a Class-I PSU and no load power consumption less than 0.21W. This PSU is capable of delivering 150 watts continuous power at 7 CFM forced air cooling or 100 watts continuous power at convection cooling and 50℃ operation temperature. Product is suitable for audio & video, display, information, and networking application.

The FSP150-P35-A24 Description

Electrical Specification
ITEM	CONDITION	SPECIFICATION
1.1 Rated Input Voltage		100Vac - 240Vac
1.2 Input Voltage Range	Continuously	90Vac to 264Vac
1.3 Input Frequency Range	Continuously	47Hz to 63Hz
1.4 Input Current	100Vac - 240Vac 47Hz to 63Hz	2.4A – 0.9A
1.5 Efficiency	115Vac, 60Hz	≥ 87%
	230Vac, 50Hz	≥ 89%
	100W Load, after warm-up 10 mins
1.6 Inrush Current	115Vac,	Shall be less than the rating of PSU critical component.
	230Vac,	(Including rectifiers, fuse surge and current limiting device)
	100% Rated Load
1.7 Power Saving	115Vac, 63Hz	≤ 0.21W
	230Vac, 47Hz	≤ 0.21W
	NO Load
1.8 Leakage Current	264Vac, 60Hz
	Touch Current	≤ 0.25mA
	Earth Leakage Current	≤ 0.75mA
2. Output Characteristics:
ITEM	CONDITION	SPECIFICATION
2.1 Output Rated Voltage		24.0V
	Convection air cooling	0 A to 4.16 A
2.2 Output Current	7 CFM Forced air cooling	0 A to 6.25 A
2.3 Output Voltage Regulation		24.0V ± 3 %
2.4 Fan Driver	24.0V Main Power load 2.5W Min.	12.0V ± 10 %
		500mA Max.
2.5 Output Voltage Ripple and Noise	115Vac, 47Hz to 63Hz 230Vac, 47Hz to 63Hz	≤ 240mVp-p
		(0.1uF/100V Ceramic Cap. and 10uF/63V Tantalum Cap.
		Paralleled between the output connector, BW=20M Hz)
2.6 Turn-On Delay Time	At 100Vac / 100W load, output voltage within regulation	≤ 1000 mSec.
2.7 Hold Up Time	100W Load, 115Vac / 230Vac 150W Load, 115Vac / 230Vac Output voltage within regulation	≥ 20 ms
		≥ 8 ms
2.8 Load Transient Response	The test step: the load regulation 0~50% or 50%~100%@1A/us,50Hz, at line voltage.	24.0V ± 5 %
3. Protection Characteristics:
ITEM	CONDITION	SPECIFICATION
3.1 Short Circuit Protection	When an internal fault occurs, or an external fault (overload or short circuit) is applied to the power supply, the power supply shall shut down and enter auto-recovery mode	Auto-recovery and no damage
3.2 Over Voltage Protection	The output trip voltage shall not exceed 35V. That will be return to normal state by	Shut down and latch.
	AC reset.
3.3 Over Power Protection	When an internal fault occurs, or an external fault is applied to the power supply, such as an overload or short	Auto-recovery and no damage
	circuit is applied to the output, the power supply shall shut down and enter
	auto-recovery mode.
3.4 Over Temperature Protection	The power supply will shutdown during abnormal thermal rise occurs. Returning back to normal operation when the power supply is cooled down and remove the AC mains input OFF and ON to reset the system.	Shut down and latch.
4. Environmental Characteristics:
ITEM	CONDITION	SPECIFICATION
4.1 Safety Standard	UL ES 62368-1	Design to meet
	CSA C22.2 No. 62368-1 TUV EN 62368-1
	IEC 62368-1
4.2 EMC	EN55032 EN61000-3-2 EN61000-3-3 EN55024	Design to meet
4.2.1 EMI :	115Vac, 60Hz	FCC CFR PART 15B CISPR 32, EN55032 Class B
Conducted Emission Radiated Emission	230Vac, 50Hz
	100% Rated Load
4.2.2 Input Current Harmonic Refer to EN61000-3-2	Harmonic distortion	Class D
4.2.3 Line Flicker
Refer to EN61000-3-3
4.2.4 Electron Static Discharge (Refer to EN61000-4-2 Energy Storage Capacitor 150pF; Discharge Resistor 330Ω)	Air Discharge: ±8KV min. Contact Discharge: ±6KV min.	Normal operation shall be continued
4.2.5 Radiated Immunity Refer to EN61000-4-3	3V/m	Normal operation shall be continued
4.2.6 Electric Fast Transients Refer to EN61000-4-4	Impulse: ±1KV L, N	Normal operation shall be continued
4.2.7 Lightning Surge Refer to EN61000-4-5	±2KV differential mode	Normal operation shall be continued
	±4KV common mode
4.2.8 Conducted Immunity Refer to EN61000-4-6	3V rms	Normal operation shall be continued
4.2.9 Magnetic Field Immunity Refer to EN61000-4-8	3A/m	Normal operation shall be continued
4.2.10 Voltage Dip Immunity Refer to EN61000-4-11	230Vac, 50Hz	Criteria Class A Class A Class B
	>95% reduction for 10 ms (0.5 cycles)
	30% reduction for 500 ms (25 cycles)
	>95% reduction for 5000 ms (250 cycles)
4.3 Cooling	Convection air cooling	100W
	7 CFM Forced air cooling	150W
4.4 Dielectric Strength (Hi-Pot)	Input to Output Input to Ground Output to Ground	3000Vac
		1500Vac
		500Vac
4.5 Temperature	Operating	-20°C to +70°C
	Storage	-40°C to +85°C
	Derating	Derate from 100% at +50°C, linearly to 50% at +70°C
4.6 Relative Humidity	Operating Storage	10% ~ 90% (non–condensing)
		5% ~ 95% (non–condensing)
4.7 Atmospheric Pressure	Operating Storage	5000M max.
4.8 Vibration	Operation, 0.01g²/Hz at 5 Hz s fffloping to 0.02g²/Hz at 20 Hz, and maintaining 0.02g²/Hz from 20 Hz to 500 Hz. The area under the PSD curve is 3.13gRMS. The duration shall be 20	Normal operation shall be continued
	minutes per axis for all three axes on all samples.
4.9 MTBF	At output power 100W and +25°C ambient, calculated per MIL-HDBK-217F	> 100,000 hours
4.10 RoHS	Lead and it’s compound (Pb) Mercury and it’s compound (Hg) Cadmium and it’s compound (Cd)	< 1000 PPM
	Hexavlent chromium compound (Cr+6) PBB	< 1000 PPM
	PBDE	< 100 PPM
		< 1000 PPM
		< 1000 PPM
		< 1000 PPM
5. Mechanical Characteristics :
ITEM	CONDITION	SPECIFICATION
5.1 Dimension (Length x Width x Height)		127.0mm * 76.2mm * 27.0mm (5 “ * 3 “ * 1.06 “)
5.2 Weight		168g (typical)
5.3 Input Connector	Input Connector (IN1)	B2P3-VH(LF)(SN), JST
		or Equivalent
5.4 Output Connector	Input Connector (CN200)	B6P-VH(LF)(SN), JST
		or Equivalent

The FSP150-P35-A24 Features

• 1.5KVac isolated between PE and RETURN
• Surge protection ±2 KV diff., ±4 KV com
• High altitude 5000 meters operation
• OTP, Brown out protection
• +12V fan driver
• Ground pad terminal
• Class -I design
• Dimension 3"x5"x1. 126"
• 100W at convection cooling, 150W at 7 CFM forced air cooling
• No load power consumption less than 0. 21W
• Design to meet IEC 62368 -1 safety standard

Product Display

About us

Raypodo  is one of best computer and Mobile phone product and service provider, who is focusing on computer components and Mobile phone spare parts production and selling. We aim to provide customers with satisfactory products and service In China and overseas.

Until now, Raypodo has three main markets include China, North America and Europe. The business is spread over more than 5 countries and 76 cities where customers is enjoy and experiencing our products and Services.

Vision

Raypodo is being the “Best Partner in Electronics , Eco-Friendly and Intelligent Technologies,” a company of world-class excellence in terms of business scale, products, corporate governance, and corporate social responsibility. For business scale, the company's goal is to surpass an annual turnover of USD 1M and to elevate its profitability to the top of the industry. For its major products, RAYPODO aims to lead the industry and become the absolute No. 1 worldwide. With regards to corporate governance, RAYPODO pursues transparency, independence, and fairness. While we look for opportunities to generate revenue and profits, we realize the importance of corporate social responsibility and strive to be a good global corporate citizen, to manufacture green products, and to give back to society.

Mission

Raypodo mission is to implement an operational excellence centered upon profitability, sound governance and improvement of shareholder returns, thereby demonstrating its determination and strength in achieving consistent profit growth.

Beliefs

Customer Satisfaction, Excellence in Execution, Innovation, and Integrity are the guiding principles, commitments, and beliefs of RAYPODO. These values are applied throughout the company's daily business operations and management.

• Customer Satisfaction

As the best partners for our customers, we attentively listen to their needs, mastering market trends and using our strong expertise to fulfill their goals.

• Excellence in Execution

With outstanding execution, we dedicate ourselves to fulfilling our commitments to customers, while creating innovative competitive advantages.

• Innovation

With open minds and innovative technology, we are at the forefront of the mass production of next-gen technology.

• Integrity

We emphasize integrity, transparency, and doing the right thing to earn the respect of our employees and trust of our customers and stakeholders to ensure solid and sustainable business operations.